Blog

Precor Error Code 38 Overload Slowdown

Mar 03, 2022

Applies to TRM600-XX, 120V Lower SW 304643-101 012 and later P30 Software Version 304716-101 002 and later TRM700-XX, 120V Lower SW 304235-105 003 and later P30 Software Version 304254-101 007 and later P30i Software Version 304756-101 002 and later TRM800-XX, 120V Lower SW 302105-104 and later P10 Software Version 303310-102 008 and later P30 Software Version ...

Precor Error Code 37 E-STOP Upper PCA/Lower PCA Mismatch / Stop Switch State Error

Mar 03, 2022

Applies to TRM800-14/18 treadmills, TRM2XX treadmills, SCL800 StairClimbers Issue symptoms TRM800-14/18 treadmills, TRM2XX treadmills Error 37 -Stop UPCA - LPCA Mismatch Error 37 may occur after an E-STOP event. If the E-STOP event is not successfully cleared in the lower PCA and the upper display believes the E-STOP has been cleared, an Error 37 will occur. Possible ...

Precor Error Code 29 Excessive AC Input Current

Mar 03, 2022

Applies to Commercial treadmills built after 2006 and before 2014. Overview Error codes 27, 28, and 29 overview, see 27, 28, 29 Overview Issue symptoms (Error 29) If the AC input current reaches a value over 20 amps or there is an AC current spike of 65 amps, the drive motor system will shut down and an Error 29 will be logged. Possible causes ...

Precor Error Code 28 Electronics Temperature Too High

Mar 03, 2022

Applies to Treadmills Overview Error codes 27, 28, and 29 overview, see 27, 28, 29 Overview Issue symptoms (Error 28) Treadmill motor controllers monitor the temperature of the motor controller output switching device. Typically, these motor controllers use a fan to force cool the output device’s heat sink. This error indicates that the heat sink temperature has exceeded maximum...

Precor Error Code 27 Motor Current Too High

Mar 03, 2022

Applies to Treadmills Overview Error codes 27, 28, and 29 overview, see 27, 28, 29 Overview Issue symptoms The motor controller monitors the amount of current being used by the drive motor. Error 27 is triggered when the motor current increases to the maximum drive motor current (approximately 20 amps). The most likely cause is a worn running belt and deck. Less likely, but ...

Precor Error Code 27, 28, 29 Overview Drive Motor Current Overloading Overview

Mar 03, 2022

Applies to Treadmills Overview Characteristics of treadmill overloading are: Most frequent cause of treadmill shutting down. Overloading is most often caused by excess deck/belt friction but can be made worse by line voltage conditions. Happens more often with heavier runners, but never walkers. In high-use clubs (10 hours or more of use per day), the decks/belts will wear out ...

Precor Error Codes with Flowchart and Warnings

Feb 21, 2022

About There is a set of standard error codes implemented across Precor cardio exercise equipment. Error codes are system generated codes that identify specific machine fault conditions. The maintenance software monitors error code event conditions, when a fault is detected, the error code is generated and stored in the Error Log or CPA(Touchscreen console Control Processing Assembly.) ...

Precor Error Code 25 Motor Controller / LPCA Hardware Error

Feb 21, 2022

Applies to TRM800-14/18 treadmills, EFX800-16 ellipticals Issue symptoms On the TRM, this error monitors the functionality of the MC. If the software detects a defect in the MC, the treadmill will stop working and Error 25 will be displayed. On the EFX, this error monitors the functionality of the LPCA. The Major processor detects that the Minor processor is not working correctly, ...

Precor Error Code 21 Too Many Maximum Consecutive Power Requests

Feb 21, 2022

Applies to Consumer treadmills, Commercial treadmills pre-2006 Issue symptoms This error monitors the treadmill's power bit reading when the treadmill operates at speeds above 1 MPH. Power bits indicate the relative time the motor controller drive circuit is switched on. Therefore, power bits is an indication of the amount of power the load is demanding from the motor controller. Error 21 ...

Precor Error Code 19 PFC Malfunction

Feb 21, 2022

Applies to TRM800-14/18 treadmills Issue symptoms The treadmill uses Power Factor Correction (PFC) to maximize the input power for greatest efficiency. This allows for fluctuations in the input voltage without affecting the performance of the treadmill. When the MC detects that the PFC circuitry is not able to correctly compensate for fluctuating input voltage, the treadmill will ...